Statistics

    Map

Twitter

Adhesive and abrasive wear resistance evaluation of a ABNT 52100 steel from a Stretch Bending Roll coated with WC-Co and NICCr applied by the HVOF Process
( Vol-5,Issue-5,May 2018 )
Author(s):

Wender Pereira de Oliveira, Pedro Américo Almeida Magalhães Junior, José Rubens Gonçalves Carneiro

Keywords:

HVOF, Pin-on-Disk, Stretch Bending Roll, ABNT 52100.

Abstract:

The tungsten carbide coatings in the cobalt matrix (WC-Co) and nickel-chromium carbide (NiCCr) are widely used to give greater resistance to abrasive wear to carbon steel. In this work, the possibility of applying these two coatings in the ABNT 52100 steel of a stretch bending roll, with the addition or not of an intermediate NiAl layer, using the thermal spray process HVOF (High Velocity Oxygen fuel), since this process has a small thermal input and allows the possibility of applying a great variety of coatings, including non-metallic ones. It was proposed to evaluate the performance of the samples in situations of high abrasive wear, also evaluating the role of the intermediate layer to improve adhesion of the coating to the substrate. For the evaluation of the resistance to abrasive wear and adhesive, the pin-on-disc tests (ASTM G99-17) and tensile tests (ASTM E8E8M-16a), respectively, were used. The surfaces of the samples were also evaluated by optical microscopy and electronic scanning. In addition, the hardness of each sample was also evaluated. With the tests, it was concluded that the samples with higher hardness and the presence of intermediate layerpresented faults in the interface of thesubstrate with coating, and the resistance to abrasive wear did not deviate much from the values in the literature.

ijaers doi crossref DOI:

10.22161/ijaers.5.5.32

Paper Statistics:
  • Total View : 155
  • Downloads : 50
  • Page No: 248-251
Cite this Article:
MLA
Wender Pereira de Oliveira et al ."Adhesive and abrasive wear resistance evaluation of a ABNT 52100 steel from a Stretch Bending Roll coated with WC-Co and NICCr applied by the HVOF Process". International Journal of Advanced Engineering Research and Science(ISSN : 2349-6495(P) | 2456-1908(O)),vol 5, no. 5, 2018, pp.248-251 AI Publications, doi:10.22161/ijaers.5.5.32
APA
Wender Pereira de Oliveira, Pedro Américo Almeida Magalhães Junior, José Rubens Gonçalves Carneiro(2018).Adhesive and abrasive wear resistance evaluation of a ABNT 52100 steel from a Stretch Bending Roll coated with WC-Co and NICCr applied by the HVOF Process. International Journal of Advanced Engineering Research and Science(ISSN : 2349-6495(P) | 2456-1908(O)),5(5), 248-251. http://dx.doi.org/10.22161/ijaers.5.5.32
Chicago
Wender Pereira de Oliveira, Pedro Américo Almeida Magalhães Junior, José Rubens Gonçalves Carneiro. 2018,"Adhesive and abrasive wear resistance evaluation of a ABNT 52100 steel from a Stretch Bending Roll coated with WC-Co and NICCr applied by the HVOF Process". International Journal of Advanced Engineering Research and Science(ISSN : 2349-6495(P) | 2456-1908(O)).5(5):248-251. Doi: 10.22161/ijaers.5.5.32
Harvard
Wender Pereira de Oliveira, Pedro Américo Almeida Magalhães Junior, José Rubens Gonçalves Carneiro. 2018,Adhesive and abrasive wear resistance evaluation of a ABNT 52100 steel from a Stretch Bending Roll coated with WC-Co and NICCr applied by the HVOF Process, International Journal of Advanced Engineering Research and Science(ISSN : 2349-6495(P) | 2456-1908(O)).5(5), pp:248-251
IEEE
Wender Pereira de Oliveira, Pedro Américo Almeida Magalhães Junior, José Rubens Gonçalves Carneiro."Adhesive and abrasive wear resistance evaluation of a ABNT 52100 steel from a Stretch Bending Roll coated with WC-Co and NICCr applied by the HVOF Process", International Journal of Advanced Engineering Research and Science(ISSN : 2349-6495(P) | 2456-1908(O)),vol.5,no. 5, pp.248-251,2018.
Bibtex
@article {wenderpereiradeoliveira2018adhesive,
title={Adhesive and abrasive wear resistance evaluation of a ABNT 52100 steel from a Stretch Bending Roll coated with WC-Co and NICCr applied by the HVOF Process},
author={Wender Pereira de Oliveira, Pedro Américo Almeida Magalhães Junior, José Rubens Gonçalves Carneiro},
journal={International Journal of Advanced Engineering Research and Science},
volume={5},
year= {2018},
}
Share:
References:

[1] Lima, C. C.,Trevisan, R. E. (2001). Aspersão Térmica: fundamentos e aplicações / Carlos Camello Lima, Roseana Trevisan. São Paulo: Artiber Editora.
[2] Papst, N. A. (2007) ASSOCIAÇÃO BRASILEIRA DE SOLDAGEM: Aspersão Térmica – Metalização. Programa de Cursos Modulares em Tecnologia de Soldagem.Módulo: Metalização. Édile Serviços Gráficos e Editora. São Paulo.
[3] Ladeira, L. W. A. (2000) Conjugados Duplex de WC-Co/NiCrAl ou NiCr, processados por aspersão térmica, para aplicações em meios corrosivos e/ou desgaste. Dissertação (Mestrado) - Curso de Pós-Graduação em Engenharia Metalúrgica e de Minas, Universidade Federal de Minas Gerais, Belo Horizonte.
[4] ASTM - American Society for Testing and Materials. ASTM G65-16 (2016b). Standard Test Method for Measuring Abrasion Using the Dry Sand/Rubber Wheel Apparatus. Pennsylvania.
[5] ASTM - American Society for Testing and Materials. ASTM G99-17. (2017). Standard Test Method for Wear testing with a Pin-on-Disk Apparatus. Pennsylvania, 2017.
[6] ASTM - American Society for Testing and Materials. ASTM E8/E8M−16a. (2016a) Standard Test Methods for Tension Testing of Metallic Materials.Pennsylvania.
[7] Marcomini, J. B. (2012) Caracterização da nova liga Fe-C-Mn-Si-Cr: Fragilização da martensitarevenida e curvas de revenimento. 182 p. Dissertação (Mestrado) – Universidade de São Paulo. São Paulo.
[8] Praxair. (2017) – Surface Tecnologies. Technical data Bulletin Coating Properties. Data Sheet. Available at: http://www.praxairsurfacetechnologies.com/components-materials-and-equipment/materials/thermal-spray-powders/carbide. Access in: 28/11/2017.