Statistics

    Map

Twitter

Casting Design Optimization for Steam Turbine Emergency Stop Valve (ESV) Housing with Computational Casting Simulation Method
( Vol-5,Issue-3,March 2018 )
Author(s):

Agus Krisnowo , Khamda Herbandono , Rudias Harmadi , Budi Nofiantoro. F

Keywords:

Design optimization, Casting simulation, Filling Velocity, Solidification, Porosity.

Abstract:

Design optimization casting emergency stop valve steam turbine, has been done with casting simulation using Magmasoft v5 software. By simulation, some casting design parameters are changed to get more optimal results. Optimization of the design of castings in this study, obtained by improving the design through changes in pouring system using bottom pouring and optimization of riser design. The result of four design casting simulation ESV housing versus filling velocity, solidification, and porosity have the same trend of location defect that is in the flange and middle body valve connection area. However quality of the simulation results, in design # 4 has a better quality of casting results based on the color gradation seen in the range of 80-90%. Although, there is still a potential defect in critical areas that have low castability. This results can be used as input for the further casting improvement and NDT inspector guidance.

ijaers doi crossref DOI:

10.22161/ijaers.5.3.11

Paper Statistics:
  • Total View : 120
  • Downloads : 20
  • Page No: 072-077
Cite this Article:
MLA
Agus Krisnowo et al ."Casting Design Optimization for Steam Turbine Emergency Stop Valve (ESV) Housing with Computational Casting Simulation Method". International Journal of Advanced Engineering Research and Science(ISSN : 2349-6495(P) | 2456-1908(O)),vol 5, no. 3, 2018, pp.072-077 AI Publications, doi:10.22161/ijaers.5.3.11
APA
Agus Krisnowo , Khamda Herbandono , Rudias Harmadi , Budi Nofiantoro. F(2018).Casting Design Optimization for Steam Turbine Emergency Stop Valve (ESV) Housing with Computational Casting Simulation Method. International Journal of Advanced Engineering Research and Science(ISSN : 2349-6495(P) | 2456-1908(O)),5(3), 072-077. http://dx.doi.org/10.22161/ijaers.5.3.11
Chicago
Agus Krisnowo , Khamda Herbandono , Rudias Harmadi , Budi Nofiantoro. F. 2018,"Casting Design Optimization for Steam Turbine Emergency Stop Valve (ESV) Housing with Computational Casting Simulation Method". International Journal of Advanced Engineering Research and Science(ISSN : 2349-6495(P) | 2456-1908(O)).5(3):072-077. Doi: 10.22161/ijaers.5.3.11
Harvard
Agus Krisnowo , Khamda Herbandono , Rudias Harmadi , Budi Nofiantoro. F. 2018,Casting Design Optimization for Steam Turbine Emergency Stop Valve (ESV) Housing with Computational Casting Simulation Method, International Journal of Advanced Engineering Research and Science(ISSN : 2349-6495(P) | 2456-1908(O)).5(3), pp:072-077
IEEE
Agus Krisnowo , Khamda Herbandono , Rudias Harmadi , Budi Nofiantoro. F."Casting Design Optimization for Steam Turbine Emergency Stop Valve (ESV) Housing with Computational Casting Simulation Method", International Journal of Advanced Engineering Research and Science(ISSN : 2349-6495(P) | 2456-1908(O)),vol.5,no. 3, pp.072-077,2018.
Bibtex
@article {aguskrisnowo2018casting,
title={Casting Design Optimization for Steam Turbine Emergency Stop Valve (ESV) Housing with Computational Casting Simulation Method},
author={Agus Krisnowo , Khamda Herbandono , Rudias Harmadi , Budi Nofiantoro. F},
journal={International Journal of Advanced Engineering Research and Science},
volume={5},
year= {2018},
}
Share:
References:

[1] Gaumann, M., Investment Casting Simulation, Calcom, USA, 2002
[2] Guo, Z., et al., Modelling of Materials Properties and Behaviour Critical to Casting Simulation, Elsevier-Materials Science and Engineering A 413-414, 2005
[3] Barzilai Philippe, et all., Simulating Foundry Operation To Increase Speed And Accuracy, Advanced Manufacturing Technology, Vol.25, No.02, 2004
[4] Rajender Singh, Introduction to Basic Basic manufacturing Processes and Workshop Technology, N.A.I Publishers ISBN 978-81-224-2316-7, India, 2006
[5] Nandogopal, M. et al, Study of Sand Casting Gating System, IJRERD SN: 2455-8761, Vol 02-Issue 11, India, November 2017
[6] Pariona, M.M., et al., Numerical Simulation for Prediction of Filling Process In a Sand Mould, Revista Latinoamericana de Metalurgia y Materiales, 28(2), 99-110, 2008
[7] Vijayaram,T.R., et al., Numerical Simulation of Casting Solidification in Permanent Metallic Molds, Journal of Materials Processing Technology 29-33, 178, 2006
[8] Krack, R., Using Solidification Simulations For Optimising Die Cooling Systems, Germany, 2007
[9] Mr. B.M. Anjikhane, Prof. N.D.Misal, MM. Gore , Review paper on Simulation of Solidification Process in casting and optimization of Riser, International journal of application or Inovation in Engineering & Management (IJAIEM), Volume 4, Issue 5, May 2015.
[10] Ferencz Peti, Lucian Grama, Analyze of The Possible Causes Of Porosity type Defect in Aluminium High Pressure Diecast Part, Scientific Bulletin of the Petru Maior University of Targu Mures, Vol. 8, no. 1. 2011